Sale!
Programmable Amp-Hour Meter with 6 Digit Display, Integrator, current indication, alarm setting & programmable shunt calibration

Programmable Amp-Hour Meter with 6 Digit Display, Integrator, current indication, alarm setting & programmable shunt calibration

Please install and activate YITH WooCommerce Wishlist to add product wishlist
Category : Amp-Hour Category : Battery Testing Application
SKU: 800AH
Download Catalogue

Description

  • Current Integrated Display
  • 4 DIG AMP-HOUR (Selectable: AH , 0.1 AH, AMin & 0.1 AMin)
  • Presetable Limit for Amp-Hour with Relay Out,
  • 6 Digit Totalizer AH Stored in EEPROM & Front Resettable
  • Displays Current in Amps
  • Lockable Scale Factor -CAL- for Various Shunts
  • Signal Input in mV from Current Shunt of 75mV/Amp
  • Application in Constant Thickness Electroplating which is Proportional to Preset AH Limit, irrespective of Voltage/ Current Variation.
  • Simultaneous Input for mV(from Current Shunt) and Battery Voltage, to measure the AH of a chargeable Battery when Voltage falls to Factory-Settable Limit( usually 10.5V for 12V Batt)

Additional information

Your custom text or HTML.

Display

6 RED 7 Segment LEDs of 0.56” character height.
Current Display

Max 9999 Amps using a shunt of current/75mV. User programmed
Amp-Hour

Max 9999 A-H for each preset cycle. (Amp-Hour range is selected by shorting Pin 17-18 at the rear)
Amp-Minute

Max 9999 A-Min for each preset cycle. (Amp-Minute is selected, opening the link between Pin 17 & 18).
Max shunt

Max value of 9999 Amp corresponding to 75mV
Totaliser

6 Digits for Amp-Hour or Amp-Min. i.e. 99,99,99. (readable for 10 sec by going into ‘total’ mode).
Limit

Up to 9999 AH or Amin. setting (In limit mode using incr./ decr. switches).
Relay Contact

One NO-P-NC of 5 Amp rating.
Trigger start

By pressing front panel switch or closing a rear external contact.
Battery Back-Up

Not required. Programmed values & readings, including A-H stored in EPROM.
Lock

Electronic lock for calibration (open link between Pin 1 & 2 to lock CAL)
Low Volt. Trigger

Set at 10.5V internally. For testing 12V Battery AH. (With Pin 3 & 4 shorted).
Increased Res.

0.1AH or 0.1AMin facility by shifting internal jumper.
Supply

220V AC 10%
Size

Front Fascia 96mm x 96mm Din Size. Depth 135mm. Cut Out : 91mm x 91mm.
Weight

800 grams

Additional Information

Display:
6 RED 7 Segment LEDs of 0.56” character height.
Current Display:
Max 9999 Amps using a shunt of current/75mV. User programmed
Amp-Hour:
Max 9999 A-H for each preset cycle. (Amp-Hour range is selected by shorting Pin 17-18 at the rear)
Amp-Minute:
Max 9999 A-Min for each preset cycle. (Amp-Minute is selected, opening the link between Pin 17 & 18).
Max shunt:
Max value of 9999 Amp corresponding to 75mV
Totaliser:
6 Digits for Amp-Hour or Amp-Min. i.e. 99,99,99. (readable for 10 sec by going into ‘total’ mode).
Limit:
Up to 9999 AH or Amin. setting (In limit mode using incr./ decr. switches).
Relay Contact:
One NO-P-NC of 5 Amp rating.
Trigger start:
By pressing front panel switch or closing a rear external contact.
Battery Back-Up:
Not required. Programmed values & readings, including A-H stored in EPROM.
Lock:
Electronic lock for calibration (open link between Pin 1 & 2 to lock CAL)
Low Volt. Trigger:
Set at 10.5V internally. For testing 12V Battery AH. (With Pin 3 & 4 shorted).
Increased Res.:
0.1AH or 0.1AMin facility by shifting internal jumper.
Supply:
220V AC 10%
Size:
Front Fascia 96mm x 96mm Din Size. Depth 135mm. Cut Out : 91mm x 91mm.
Weight:
800 grams

Related products